SMW Accu-Smart 60 SMW Accu-Smart 60 SMWAccuSmart60 :: Industrial Electronic Repair

Links Menu

Home
About Us
Repair Lab
Thermal Imaging
Manufacture's Repaired
Get Quote
Forum
Forum2
Repair Service Form
Credit Application Free Estimate Credit Application
Monitor Repair Monitor Repair
Power Supply Repair Power Supply Repair
Board Repair Board Repair

Get Repair Pricing

Manufacture:

Part #:



Contact Menu

Email Sales
Email Shop
Email Parts
Contact Info
1-336-969-0110

  
SMW Accu-Smart 60 SMWAccuSmart60

  Posted by NICOLAS AVELLANEDA on Monday, October 24 2022

SMW Accu-Smart 60 need user manual and or maintenance manual



  Current thread:

Kristel L.P. kristel corp 17 monitor

tagged Comments
SMW Accu-Smart 60

  Posted by STEVE TELLER on Friday, November 22 2019

#SMWAccuSmart60 Hello, we have an accu-smart 60 installed on a fryer mc-40 vertical milling machine with a ge-fanuc series 21i-mb controller. Everything was working the way it should until we shut the machine down to have a tech from Fryer install door locks. After the door locks were installed & verified they were working correctly we started to run production. While the machine was drilling the indexer suddenly indexed when it wasn't suppose to. I looked at the schematic for the door locks & the actual wiring to compare them. The locks were wired to the schematic. I was told that by entering M11 & pushing cycle start that the indexer would index, which it did. After the indexer stops you reenter M11 & it should index again, which it won't. In order to index the indexer again we have to push reset, enter M11 & push cycle start & it will index again. The operator told me he never had to push reset to get the indexer to index again. Everytime he indexes the indexer, before the door locks were installed, he just keeps entering M11 & cycle start. Now after indexing the indexer he has to push reset. Looking in the accu-smart manual under maintenance, symptom # 1, "control will not accept m-code signals". It states that parameter "08" must be set at 0 or 1. If it is set at 2 the remote start will be disabled. The problem I have is that I believe I need a laptop to do this, am I correct about the laptop ? The program engineer verified that the program in the Fryer is correct.



  Current thread:

SMW Accu-Smart 60 SMWAccuSmart60
  Kristel L.P. kristel corp 17 monitor

View Parent Message

View Manufacture

Return Home
to SMW Accu-Smart 60 Repair

*Tagged Manufactures SMW Accu-Smart 60

*Tagged List
Need to get your
SMW Accu-Smart 60 Repaired?
Quickly Hire our Service Dept
to do the work for you!

Credit Application Form
Free Estimate


Contact Shop 1-336-969-0110



If you need your SMW Accu-Smart 60 unit tested or repaired
then give us a call at 1-336-969-0110.
We give fair estimates and offer a extended warranty on repairs of SMW Accu-Smart 60 units.


Reply to the Message Below!
OLD Topic: Repair of SMW Accu-Smart 60 kristel corp 17 monitor
Your name:
Valid Email Address Required:
Phone Number:
Your Location:
Subject:
Comment about
SMW Accu-Smart 60:
You can contact us at 1-(336)-969-0110
We are open Monday to Saturday from 9am till 6pm EST
and yes the technicians & engineers work on Saturday!

Recent Questions

  • A   B   C   D   E   F   G   H   I   J   K   L   M  
  • N   O   P   Q   R   S   T   U   V   W   X   Y   Z  

  • Disclaimer: This website is not sanctioned or approved by any manufacturer listed.
    "Industrial Electronic Repair" is not an authorized distributor or representative
    for the listed manufacturers or tradenames.


    Teijin Seiki Servo Drive
    Teijin Seiki



    NSK Servo Drive
    NSK


    Etasis Power Supply
    Etasis



    Vickers Servo Drive Repair




    Nikki Denso Servo Drive Repair

    Board Repair
    Forum
    Parts




    Hosted by

    ABCDEFGHIJKLMNOPQRSTUVWXYZ
    IERNC Created this page in 0.110834 seconds